目录第一章前言........................................41.1编制说明.........................................41.2钢结构安装新技术、新工艺、新设备的应用...4第二章工程概况、施工难点及对策.................52.1工程概况.........................................52.2施工难点及对策.................................5第三章塔吊方案选择...............................73.1吊装设备选择的基本原则.......................73.2塔吊布置..........................错误!未定义书签。3.3塔吊的基本参数.................................83.4塔吊安装的有关数据..............错误!未定义书签。3.5塔基施工..........................错误!未定义书签。3.6塔吊安装..........................错误!未定义书签。3.7塔吊附着..........................错误!未定义书签。3.8塔吊拆除..........................错误!未定义书签。3.9安装、拆除场地所具备的条件....错误!未定义书签。第四章施工组织机构...............................94.1项目组织机构图.................................94.2项目部主要管理人员名单及主要职责.........10第五章施工部署及施工计划.......................115.1钢结构总体安装思路............................115.2工期计划及工期确保措施.......................115.3机械设备计划..................................145.4现场用电量计算................................165.5劳动力计划.....................................165.6施工协调与配合................................17第六章钢结构安装.................................206.1现场平面布置...................................206.2钢结构施工流程................................216.3构件的分段.....................................226.4施工准备.......................................236.5钢构件和材料的进场与验收...................236.6钢结构构件主要连接节点......................246.7地脚螺栓的预埋安装施工顺序.................256.8钢柱的安装.....................................276.9钢梁的安装.....................................306.10中部桁架的安装.................错误!未定义书签。6.11斜撑及阻尼器的安装.............错误!未定义书签。6.12顶部悬挑的安装..............................326.13灯笼结构的安装.................错误!未定义书签。6.14顶金字塔结构的安装............错误!未定义书签。第七章测量控制..................................347.1测量控制的主要内容...........................347.2测量控制的基本构思...........................347.3测量控制的准备工作...........................347.4测量控制.......................................347.5注意事项.......................................40第八章高强螺栓安装..............................418.1安装前的准备...................................418.2高强螺栓安装施工流程........................418.3质量控制.......................................418.3质量控制.......................................428.4施工检验.......................................428.5注意事项..........................错误!未定义书签。第九章焊接方案......................错误!未定义书签。9.1焊前准备...........................错误!未定义书签。9.2焊接...............................错误!未定义书签。9.3焊接质量控制程序................错误!未定义书签。第十章质量保证措施.................错误!未定义书签。10.1质量目标.........................错误!未定义书签。10.2质量保证体系文件...............错误!未定义书签。10.3质量保证体系....................错误!未定义书签。10.4质量控制措施....................错误!未定义书签。10.5安装质量控制标准...............错误!未定义书签。10.6构件验收控制目标...............错误!...
VIP
